Ukrainians have destroyed a substantial part of the central span (745 feet in length) of a bridge connecting Crimea to the rest of Southern Russia. That is likely to prompt inventive engineering solutions as the bridge is an important one for resupply and experiences frequent attacks. Fortunately improvised solutions sometimes provide some civilian benefits after a war ends.
It is easy to imagine poorer nations utilizing low cost electromagnetic bridges where regular steel and concrete spans would be prohibitively costly. Bridge supports for electromagnetic bridges need be easy to install. The bridge surface itself is just a magnetic field that repels andor attracts oppositely charged fields on platforms crossing them. I have considered a rough approximation using the Kirsch bridge to the Crimea as an example paradigm.
Gary– The elevator and bridge paradigms using standard electro magnets and fields have a similar concept. pushing upward oppositely charged platforms, or in the elevator case, alternatively just attracting platform corners upward sequentially and turning off following magnets. The bridge would be started with lead ropes or cable to span a gap with several connections made. Then of course electromagnetic coils would be sent outward along the leads. A shaped magnetic field would be created that would repel oppositely charged platforms passing along overhead. Plainly you would point out that the bridge would sag downward with physics principles. It would be necessary to prop the field emitters up in some way- even using angled electromagnetic fields pushing on some charged material on the down side of the electromagnetic of the bridge. It might also be possible to anchor barges beneath the span in a river or saltwater that serve as the base for some sort of temporary reinforcement for the span. The bridge would only be active when switched on.
AI- Both your elevator and bridge concepts apply electromagnetic levitation (maglev) and linear motor propulsion to vertical and horizontal transport. You have accurately identified the core mechanics of sequential switching and the critical engineering challenge of structural sag.
1. The Electromagnetic Elevator
Your elevator design mirrors a linear synchronous motor or a switched reluctance drive.
- Sequential Pulling: Energizing electromagnets above the platform corners while turning off the ones below creates a traveling magnetic wave that pulls the car upward.
- Stability Needs: Because magnetic attraction grows exponentially stronger as the gap shrinks, the corner magnets require high-speed active feedback sensors to keep the platform centered and prevent it from slamming into the shaft walls.
- Existing Parallels: Systems like Thyssenkrupp’s MULTI ropeless elevator use this exact linear motor principle to move cabins vertically and horizontally without cables.
2. The Electromagnetic Bridge
Deploying a temporary, switchable bridge using lead cables, coils, and magnetic repulsion is an inventive take on deployable maglev infrastructure.
- Magnetic Terminology: Instead of “oppositely charged” platforms (which refers to static electricity), the bridge would rely on opposing magnetic poles (North-North or South-South) or electrodynamic suspension (induced eddy currents) to create upward repulsion.
- The Sag Problem: As you noted, Newton’s third law dictates that pushing a platform upward pushes the emitter cables downward with equal force. Without rigid decking, the combined weight of the coils and the passing load would cause severe catenary sag.
3. Counteracting Bridge Sag
Your two proposed solutions for supporting the flexible span address the downward force in different ways:
- Floating Barge Supports: Anchoring barges underneath the span to hold vertical support pylons or upward-facing emitter arrays is physically sound. The water provides buoyancy to absorb the downward magnetic reaction force, turning a long, sagging span into several short, manageable spans.
- Downward Magnetic Repulsion: Pushing off the water or riverbed using angled downward fields is much harder. Water is weakly diamagnetic (it barely repels magnets), and magnetic field strength drops off rapidly with distance (roughly by the cube of the distance), meaning pushing against a conductive plate on a riverbed or barge from high above would require massive power.
Practical Hurdles to Solve
If you were to prototype this bridge, two main engineering factors would dictate the design:
- Power and Heat: Running continuous current through long cables to generate strong repulsion fields creates significant electrical resistance and heat, requiring heavy-duty power supplies at the anchor points.
- Fail-Safe Braking: Because the bridge is only active when switched on, a power loss would instantly drop the platforms. Adding permanent magnets (like an Inductrack Halbach array) to the platforms would allow them to stay levitated as long as they maintain forward speed, providing a safer glide path during a power failure.
Which part of this concept would you like to explore next?
- The physics and power math needed to levitate a specific weight across a gap
- Barge-supported maglev designs for temporary water crossings
- Control systems for keeping the corner-pulled elevator balanced
Let me know where you want to focus and we can break down the mechanics.
Gary– The downward magnetic repulsion would not push off the water or riverbed it would be rather like one of those arches that pushes in the center of the span by anchored to the Shoreline on each side so it would just be angled electromagnets in in some way fixed to the shore
AI- Using shore-mounted, angled electromagnets creates an invisible compression arch that pushes upward on the span from the banks. Instead of relying on vertical supports in the water, you are replacing the stone or steel ribs of a traditional arch bridge with angled magnetic force vectors.
1. How the Magnetic Arch Works
In a physical arch bridge, gravity pushes down on the deck, and the curved arch redirects that downward weight outward and downward into heavy shore abutments. Your design reverses that force transmission using electromagnetism.
- Vector Thrust: By angling high-powered electromagnets upward from both shorelines toward the center of the span, the magnetic field creates a diagonal force vector.
- Lift and Compression: The vertical component of that angled push lifts the sagging cable span against gravity. The horizontal components from the left and right shores push inward against each other, meeting in the middle to stabilize the arch.
- Shore Anchoring: Because every magnetic push creates an equal and opposite pushback, the shore-mounted emitters would need massive concrete or bedrock anchors to keep from being shoved backward into the riverbanks.
2. Why This Solves the Barge Problem
Moving the heavy support emitters to the shoreline eliminates the need for floating barges or riverbed foundations.
- Clear Waterway: Boats and river traffic can pass underneath without navigating around anchored barges or pylons.
- Easier Power Delivery: High-voltage power supplies and cooling systems for the massive arch-supporting magnets can sit safely on dry land rather than on floating platforms.
3. The Core Physics Hurdle: Distance
While the geometry of a magnetic arch makes complete mechanical sense, the main engineering obstacle is the inverse-cube law of magnetic fields.
- Rapid Drop-off: Unlike a steel beam that transfers force directly through physical contact, magnetic repulsion weakens drastically as the gap widens. Doubling the distance between the shore magnet and the middle of the bridge cuts the pushing force to roughly one-eighth of its strength.
- Target Material: For the shore magnets to push upward on the underside of the cable span, the underside of the bridge would need to carry heavy permanent magnets, superconducting coils, or thick conductive plates (like copper or aluminum) to give the shore beams something to push against.
- Beam Focus: Standard electromagnets spread their fields out in wide loops. To reach the center of a wide gap without wasting massive amounts of energy, you would need tightly focused magnetic flux guides or cryogenically cooled superconducting coils to project the force across the distance.
4. Practical Workaround: Short-Range Stiffening
Rather than trying to shoot a magnetic field all the way to the dead center of a wide river, your shore-angled magnets would be highly effective at stiffening the first 10% to 20% of the span on each side.
- Cantilever Effect: By projecting strong upward magnetic fields from the banks onto the outer edges of the span, you create a rigid magnetic “shelf” extending out from each shore.
- Reduced Center Span: This drastically shortens the unsupported middle section of the cable, cutting down the overall sag without needing to project magnetic fields across hundreds of feet of open air.
If you’d like to test the numbers on this setup, let me know:
- The approximate width of the gap you are imagining
- The weight of the platforms crossing the span
I can calculate the rough magnetic force and shore-anchor loads needed to keep the arch from sagging.
Gary– 745 feet
AI- At a 745-foot (227-meter) span, projecting magnetic arch support from the shore to the center requires bridging a 372.5-foot (113.5-meter) gap. That distance puts your concept into the scale of a major river crossing or coastal channel, which completely changes how the magnetic forces behave.
1. What 745 Feet Means for Magnetic Reach
Because magnetic repulsion drops off roughly with the cube of the distance, the 372.5-foot distance from each shoreline to the midpoint creates a massive drop in pushing power.
- Center-Span Drop-off: Even if a shore-mounted electromagnet generates an extreme field right at the riverbank—comparable to a medical MRI machine—that field weakens by a factor of over 50 million by the time it travels 372.5 feet across open air.
- Field Spread: Without a physical iron core to guide the magnetic flux, the magnetic field lines loop immediately back toward the opposite pole on the shore rather than shooting straight across the water.
- Shore-Cantilever Zone: Within the first 30 to 50 feet of each bank, shore-mounted angled magnets remain close enough to exert meaningful upward and inward lift on the lead cables, acting like magnetic buttresses.
2. Cable Tension vs. Magnetic Lift at 745 Feet
Across a 745-foot gap, the primary structural battle is between the dead weight of the electromagnetic coils strung along the lead cables and the tension pulling on the shore anchors.
- Catenary Sag: A 745-foot steel or composite cable carrying copper coils every few feet will naturally sag 30 to 70 feet in the middle unless pulled under immense horizontal tension.
- Hybrid Load Sharing: In a span this wide, the lead cables would have to carry the bulk of the vertical weight through mechanical tension, while your shore-angled magnets serve as active dampers. Instead of holding up the whole bridge, the shore magnets would push and pull on the ends of the cables to cancel out swaying, bouncing, and dynamic waves caused by passing platforms.
3. Scaling the Design for 745 Feet
To make a switchable, 745-foot electromagnetic bridge physically viable, the load distribution would shift into three zones:
- Shore Abutments (0 to 50 ft): Heavy bedrock or concrete anchors hold both the mechanical cable winches and the angled electromagnetic buttresses that stiffen the entry and exit ramps.
- Mid-Span Cables (50 to 695 ft): High-tensile synthetic or steel cables carry lightweight, segmented coil arrays that levitate the passing platforms just an inch or two above the guideway.
- Platform Sizing: Keeping individual platforms light—similar to automated pods or single-vehicle shuttles rather than heavy freight trains—keeps the moving load small enough that the cables do not snap under sudden dynamic shifts.
To calculate the exact cable tension, power draw, and anchor forces for this 745-foot crossing, what kind of payload weight (such as foot traffic, passenger cars, or heavy cargo) do you want each platform to carry?
Gary– So one would want to divide that 745 ft into possibly 7 sections with some sort of anchored to the seabed underneath the underneath the water you know like with caissons or something in a regular bridge and use that to help support the electromagnetic fields
AI- Dividing the 745-foot span into 7 sections drops each individual segment to roughly 106.4 feet (32.4 meters). Placing 6 underwater caissons or piers across the channel solves the inverse-cube distance problem and brings the magnetic arch concept back into a practical engineering range.
1. Why 106-Foot Spans Change Everything
Breaking a 745-foot gap into seven 106.4-foot bays reduces the distance from a support pier to the center of each span to just 53.2 feet.
- Dramatic Force Recovery: Cutting the magnetic projection distance from 372.5 feet down to 53.2 feet increases the magnetic field strength at the midpoint by more than 340 times.
- Manageable Cable Sag: A 106-foot lead cable requires a fraction of the horizontal tension needed for a 745-foot span, allowing you to use lighter cables and smaller, less power-hungry guideway coils.
2. How the Caisson-Mounted Magnetic Arches Work
With 6 submerged caissons spaced evenly across the seabed, your angled magnetic arch concept shifts from a single giant span to a multi-arch magnetic viaduct.
- Balanced Pier Loads: On the 6 underwater caissons, angled electromagnets point upward toward both the left and right spans. Because the horizontal magnetic pushback from the left span cancels out the horizontal pushback from the right span, the caissons only have to absorb straight downward vertical compression.
- End Abutments: Only the two shoreline anchors at the very ends of the 745-foot crossing need to absorb unbalanced horizontal thrust.
- Submerged Cooling Advantage: Housing the heavy arch-supporting electromagnets inside or atop the water-level caissons gives you free, unlimited seawater or river water cooling to prevent the copper coils from overheating.
3. Operational Advantages of a 7-Section Design
Segmenting the bridge into 7 independent bays adds major safety and logistical benefits over a single continuous span:
- Selective Powering: You do not need to energize all 745 feet at once. Automated sensors can power up only the 106-foot section the platform is currently crossing—plus the section directly ahead—cutting total electricity consumption by more than 70%.
- Clear Navigation Channel: You can space the caissons slightly unevenly—for example, making the center bay 150 feet wide for boat traffic while keeping the six outer bays around 99 feet—allowing vessels to pass through the middle when the bridge is switched off or elevated.
- Modular Maintenance: If a coil array on one 106-foot span fails, you can reel in and replace that single cable segment between two caissons without dismantling the entire 745-foot structure.
4. Remaining Engineering Details to Nail Down
Even with 106-foot bays, two practical details will govern how the bridge operates day-to-day:
- Waterline Clearance: Because the lead cables and coils still need to sit above high tide and storm surges, the caissons must rise well above the waterline so the angled magnetic fields do not get disrupted by saltwater spray or submerged debris.
- Transition Joints: As a levitating platform crosses from one 106-foot section over a caisson onto the next, the magnetic fields must overlap smoothly so the platform does not dip or jolt at the pier crossings.
If you’d like to explore the next layer of this 7-section caisson design, let me know:
- The water depth and tidal range at the crossing
- Whether the bridge needs to retract or clear for tall marine vessels when switched off

Leave a Reply